Disclosure: This post is sponsored by Velvet Finishes, however all opinions and multi-colored shelves are 100% mine. Affiliate links included in this post.
Sweet Lord, it is unbelievable to me how much a person who has been on this earth for less than five years can amass. The sheer number of stuffed animals that the Circus owns is unfathomable to me. She has little plastic horses in every shape, size, breed, and color. Let’s also not discount the other varieties of plastic animals we have on hand: a bald eagle, a grizzly bear, a mountain lion, a silver back gorilla, a water buffalo – and she can specifically identify each of them.
All of the paraphernalia that comes with four year olds is just cra-cra.
If you’ve followed along with the 70’s Landing Pad renovation, you know that we took what was the master bedroom walk-in closet and turned it into the Circus’ playroom. It worked out perfectly, as the closet backed up right to her bedroom.
However, walking into that playroom was essentially like walking into a black hole of toys. Consider yourself blessed if you only stepped on one plastic horse that made you mutter a cuss word or two under your breath. When we moved in, we just kind of threw all her toys in there, threw up a couple cheap shelves and called it a day.
That was a mistake.
This space desperately needed shelves that didn’t bow in the middle and lots of them. Doing a “spinoff” of the bathroom shelving at our previous house in the Circus’ playroom didn’t occur to me until last week. So, this past weekend I put these bad boys in and life in the playroom is a touch more organized – and cute if I do say so myself. 😉
And let’s just be real, we all know those shelves aren’t going to stay that organized after a couple of days, hell, a couple of hours. I gave it a shot though.
These shelves are so easy to make, y’all. If you can nail a piece of wood to a wall, then you can build these. I built all four of those shelves in about an hour for about $50. Of course if your walls are longer or shorter, your cost would be different. Here’s how to make them.
As a reference point, my shelves are 58″ wide. These are the supplies I needed for the four shelves.
- 2 – 1″ x 2″ x 8ft Furring Strips (supports for shelves)
- 2 – 1″ x 12″ x 10ft Common Boards (actual shelves)
- 20 feet of Decorative Molding – I used this basic chair rail.
- Stud Finder
- Nail Gun & Nails or Hammer and Finish Nails
- Saw (either a miter saw, circular saw or handsaw. I used our miter saw. You could also pre-measure and have the pieces cut at your local home improvement store.)
- Level – a small one and a large one are ideal for this project, but a small one will do the job if necessary.
- Measuring Tape
- Paint: I used Velvet Finishes Paint in Exotic, Boheme, Stately and Glamorous.
For each shelf you are building, cut at least two 11″ pieces of the 1″ x 2″ furring strip. If your shelves are close to the same width as mine or longer, you will need to cut at least one more 11″ piece of the 1″ x 2″ furring strip for additional supports in the middle of the shelf.
Grab your measuring tape, stud finder and pencil. Using the measuring tape, mark on each side of the wall how high up you want your first shelf to be. My lowest shelf was 27″ off the ground to accommodate for storage underneath. The rest of the shelves are 12″ apart from one another.
After making the marks on the walls where you want the shelves to be, use one of the 1″ x 2″ strips you cut and place it on the mark, then draw a line under the piece. Use your stud finder to locate studs where the line is and mark those on the wall.
Place the 1″ x 2″ piece along the mark you made. Use a small level to ensure the strip is level, then nail it in where the studs are located behind the wall.
Repeat this process on the opposite wall at the same height.
Cut a 1″ x 12″ board down to the width between the two walls. (Mine was 58.”) Place it on top of the two strips you just attached to the wall.
Place a level on top of the shelf (a larger level if you have one) to check to make sure its level and then nail the 1″ x 12″ board from the top down into the strips of wood you attached on the side walls.
For these shelves, I needed an additional middle support. To do that, use the stud finder to locate where the studs are under the shelf, then place one of the 1″ x 2″ strips just under the shelf where a stud is located. Nail the strip in place, then nail the shelf into the strip from the top down as you did with the sides.
If you don’t have a stud in the center or close to the center of the wall, then you can do two supports split between the middle of the shelf where studs are.
Cut a piece of molding, I used chair rail, down to the width of your shelves. Mine was 58.” Attach to the front of the shelf even with the top of the shelf.
Repeat this entire process for as many shelves as you want to build.
Paint those bad boys!
With Velvet Finishes Paint, there is usually no prep required and it has a primer already built-in.
I just brushed the color right on. Each shelf got two coats of paint. Velvet Finishes also has a built-in topcoat, so I didn’t worry with a topcoat for these either. If I had been painting something like a tabletop or end table that would see a lot of drinking glasses and other action, I would have used an additional topcoat.
Are those just not the most fun shelves you’ve ever seen?
The Circus was using the lower shelf where the typewriter, phone and cash register are as her “office” the other night. Apparently, the shelves are cute, colorful, functional and also moonlight as a work space for her. 😉
Do you have any places you could use some shelves like this?
You can see how I made these shelves for extra storage in our bathroom here.
You’re probably going to want to see these too…
Disclosure: This post is sponsored by Velvet Finishes, however all opinions and multi-colored shelves are 100% mine.