The 70’s Landing Pad is actually starting to not look like a construction zone.
Well, it’s starting to not look like a construction zone in the living room, dining room and hallway anyway.
After getting paint on the walls week before last, we’ve been putting down the new flooring in the hallway, living and dining rooms. This flooring will also go in the kitchen, stair landing and in the downstairs foyer as well, we just haven’t gotten that far yet. I’m finally moving past the point of “Oh my word, what have we gotten ourselves into?” to “Oh my word, it actually looks like a house and it’s pretty!” We still have quite a ways to go in the overall renovation, but there is a light at the end of the tunnel, y’all.
NuCore is an engineered floor that has a tough top layer of luxury vinyl adhered to a stable, rigid, and waterproof core. I’ll be the first to say there isn’t a thing about this flooring that looks cheap or even like vinyl – I’ll also admit I had my doubts in the beginning. I partnered with Floor & Decor on the flooring and after a slew of emails full of questions about NuCore between myself and Sarah from Floor & Decor, we finally opted to go with the NuCore Cocoa Oak Handscraped Planks.
One of my doubts was how easy installation was supposed to be. Word on the street was that it snapped together (tongue and groove), no glue or nailing required and it could go over most any existing floor, with the exception of carpet.
Word on the street was accurate.
How to Install NuCore Flooring
- NuCore Flooring
- Speed Square
- Rubber Mallet
- Utility Knife (use new, sharp blades)
- Measuring Tape
- Jigsaw & Drill (Needed only for cutting around door frames and other odd edges.)
Unlike hardwood, NuCore does not have to acclimate to your home’s temperature before being installed. You can start as soon as you get it.
You can install NuCore over most existing flooring. Carpet is an exception. If you want to put it where carpet currently is, you will need to remove the carpet first, which is what we had to do. Pull up any staples that are left from the carpet pad and remove any carpet tack strips.
For your first row, you will simply snap the short edges of the flooring together, which easily lock into one another. After finishing the first row, place a few pieces of the flooring vertically along the baseboard of the room. Put your first row flush against these pieces. This will keep your first few rows of flooring from sliding in the beginning.
For the second row of flooring, you will snap the tongue and groove into each other.
Simply hold a piece of NuCore at a 45° angle and snap it into the piece in front of it.
Use a rubber mallet to secure the joints.
You do want to make sure you stagger your joints as shown below.
You will have to cut pieces in order to do this sometimes and obviously you will have to cut pieces as you get to the end of rows. To cut NuCore, measure to determine what length you need, mark it on the plank, score it with a utility knife and snap it at the cut.
After installing all the flooring, you will want to trim out around the edges with quarter round molding to cover the small gap. If you have to go around door trim or jambs, you can cut the wood with a jigsaw. Mark where you need to cut, drill a small hole to get you started, then use the jigsaw to cut the flooring.
Grunt Labor and I made a quick video to show you how to install NuCore.
It is really as simple as it looks. And when it’s installed, it looks just like hardwood. It’s gorgeous. I’m also pretty pumped about the fact that it’s waterproof, so that when the Circus doesn’t tell me she spilled her juice hours later, it won’t be that big of a deal. 🙂
UPDATE: I DID A REVIEW OF OUR NUCORE FLOORING ONE YEAR LATER. YOU CAN READ ABOUT IT HERE.
What are your thoughts?
You know you don’t wanna miss any of this crazy.
Sign up to get my posts delivered to your inbox here.
Stalk Me Here:
Disclosure: This post was in partnership with Floor & Decor. However, all opinions and love of easy-to-install flooring are 100% mine.
*Affiliate links may be contained in this post. That just means if you click on one of those links and buy something, I may receive a small commission, but you won’t pay a dime more. Thanks for supporting my cheap beer habit and helping to send my kids to college.